SINGA は Linux プラットフォームで開発されました。
下記のライブラリを必要とします。ご確認ください。
glog version 0.3.3
google-protobuf version 2.6.0
openblas version >= 0.2.10
zeromq version >= 3.2
czmq version >= 3
zookeeper version 3.4.6
オプション
すべての Dependencies をインストールするには
# thirdparty フォルダに移動 cd thirdparty ./install.sh all $PREFIX
$PREFIX がシステムパス (例 /usr/local/) でない場合は、下記の変数を exportコマンドで設定してください。
export LD_LIBRARY_PATH=$PREFIX/lib:$LD_LIBRARY_PATH export CPLUS_INCLUDE_PATH=$PREFIX/include:$CPLUS_INCLUDE_PATH export LIBRARY_PATH=$PREFIX/lib:$LIBRARY_PATH export PATH=$PREFIX/bin:$PATH
インストールスクリプトの詳細は、このページの下にあります。
GNU autotools を使用します。まずは GCC (version >= 4.8) のバージョンを確認してください。
SINGA をビルドする2つの方法を用意しました。
Git コマンドを使用して Github から最新のソースコード(レポジトリ)をクローンし、次のコマンドを実行します。
$ git clone git@github.com:apache/incubator-singa.git $ cd incubator-singa $ ./autogen.sh $ ./configure $ make
Note: nusinga アカウントの singa repository は Apache Incubator project として使用していたものなので、最新ではありません。ご注意ください。
Release パッケージをダウンロードし、次のコマンドを実行します。
$ tar xvf singa-xxx $ cd singa-xxx $ ./configure $ make
ある機能は外部ライブラリに依存します。 それらの機能を利用するために、--enable-<feature> を付けてコンパイルしてください。 例えば、lmdb サポートを追加するには
$ ./configure --enable-lmdb
うまくコンパイルが成功すると、.libs/ フォルダ内に libsinga.so と実行ファイル singa が生成されます。
特定の dependent ライブラリが見つからない場合、次のスクリプトを実行してください。 # thirdparty フォルダに移動 $ cd thirdparty $ ./install.sh LIB_NAME PREFIX
インストールパスを指定しない場合、ライブラリは(ソフトウェアが指定した)デフォルトのフォルダにインストールされます。 例えば、デフォルトのフォルダに zeromq ライブラリをインストールするには、次のコマンドを
$ ./install.sh zeromq
別のフォルダ(e.g., PREFIX)にインストールするには、次のコマンドを
$ ./install.sh zeromq PREFIX
/usr/local フォルダにすべての Dependencies をインストールするには、次のコマンドを
$ ./install.sh all /usr/local
ライブラリ名(LIB_NAME)は以下のとおりです。
LIB_NAME Library czmq(注) czmq lib glog glog lib lmdb lmdb lib OpenBLAS OpenBLAS lib protobuf Google protobuf zeromq zeromq lib zookeeper Apache zookeeper
(注) czmq をインストールする時、zeromq のパスを -f オプションで指定する必要があります。 コマンドは次のとおりです。
$./install.sh czmq /usr/local -f=/usr/local/zeromq
結果、/usr/local フォルダに czmq がインストールされます。
A1: This means the compiler cannot find the OpenBLAS library. If you installed it to $PREFIX (e.g., /opt/OpenBLAS), then you need to export it as
$ export LIBRARY_PATH=$PREFIX/lib:$LIBRARY_PATH # e.g., $ export LIBRARY_PATH=/opt/OpenBLAS/lib:$LIBRARY_PATH
Q2: You need to include the folder of the cblas.h into CPLUS_INCLUDE_PATH, e.g.,
$ export CPLUS_INCLUDE_PATH=$PREFIX/include:$CPLUS_INCLUDE_PATH # e.g., $ export CPLUS_INCLUDE_PATH=/opt/OpenBLAS/include:$CPLUS_INCLUDE_PATH # then reconfigure and make SINGA $ ./configure $ make
A3:You can try following command:
$ make CFLAGS='-msse2' CXXFLAGS='-msse2'
A4:After install google protobuf by make install, we should install python runtime libraries. Go to protobuf source directory, run:
$ cd /PROTOBUF/SOURCE/FOLDER $ cd python $ python setup.py build $ python setup.py install
You may need sudo when you try to install python runtime libraries in the system folder.
A5: SINGA does not depend on gflags. But you may have installed the glog with gflags. In that case you can reinstall glog using thirdparty/install.sh into a another folder and export the LDFLAGS and CPPFLAGS to include that folder.
A6:Please install glog individually and try :
$ make CFLAGS='-stdlib=libstdc++' CXXFLAGS='stdlib=libstdc++'
A7: This is because the zookeeper is not started. Please start the zookeeper service
$ ./bin/zk-service start
If the error still exists, probably that you do not have java. You can simple check it by
$ java --version
A8: You can compile OpenBLAS by
$ make ONLY_CBLAS=1
or install it using
$ sudo apt-get install openblas-dev
or
$ sudo yum install openblas-devel
It is worth noting that you need root access to run the last two commands. Remember to set the environment variables to include the header and library paths of OpenBLAS after installation (please refer to the Dependencies section).
A9: This means the linker found libstdc++.so.6 but that library belongs to an older version of GCC than was used to compile and link the program. The program depends on code defined in the newer libstdc++ that belongs to the newer version of GCC, so the linker must be told how to find the newer libstdc++ shared library. The simplest way to fix this is to find the correct libstdc++ and export it to LD_LIBRARY_PATH. For example, if GLIBC++_3.4.20 is listed in the output of the following command,
$ strings /usr/local/lib64/libstdc++.so.6|grep GLIBC++
then you just set your environment variable as
$ export LD_LIBRARY_PATH=/usr/local/lib64:$LD_LIBRARY_PATH